Ignore:
Timestamp:
06/25/12 19:08:33 (10 years ago)
Author:
jgipsl
Message:
  • Updated LMDZRERP experiment to use config.def and output.def files
  • Better comments in lmdz.card (I hope)
  • Removed LMDZ_Freq_aero and LMDZ_Length_aero from lmdz.card. Option not longer existing in lmdz.driver
Location:
CONFIG/UNIFORM/v5/LMDZOR_v5/EXPERIMENTS/LMDZOR
Files:
2 edited

Legend:

Unmodified
Added
Removed
  • CONFIG/UNIFORM/v5/LMDZOR_v5/EXPERIMENTS/LMDZOR/amip/COMP/lmdz.card

    r1750 r1787  
    1111#LMDZ_Physics=NPv3.1 
    1212 
    13 # You can choose here the name of create_etat0 you want to use 
    14 # If noting is defined here, the job will get the JobName in the file  ../CREATE/config.card 
     13# Set the variable CREATE needed further below to find the initial and boundary condition files. 
    1514CREATE=ELI-${RESOL_ATM_3D} 
     15 
     16# ByPass_hgardfou_teta=y : modify teta_ parameters for following CumulPeriod only 
    1617ByPass_hgardfou_teta=n 
     18 
     19# ByPass_hgardfou_mats=y : set parameter purmats=y for following CumulPeriod only 
    1720ByPass_hgardfou_mats=n 
     21 
     22# Number of periods where to set parameter adjust=y before switching to adjust=n 
     23# For adjust=n, set LMDZ_NbPeriod_ajust=0.  
    1824LMDZ_NbPeriod_adjust=3 
    19 # LMDZ_NbPeriod_adjust=0 
    20 # To force usage of this Bands file, put LMDZ_NbPeriod_adjust=0 and replace XXXXXXX by Restart Job Name 
     25 
     26# To force usage of specific Bands file, put LMDZ_NbPeriod_adjust=0 and replace XXXXXXX by Restart Job Name 
    2127# LMDZ_Bands_file_name=${ARCHIVE}/IGCM_OUT/IPSLCM5/XXXXXXX/ATM/Debug/XXXXXXX_Bands_96x95x19_3prc.dat_3 
    2228 
     
    4248 
    4349# Nugding : ok_guide=y/n 
     50# If ok_guide=y, add nudging files(u.nc, v.nc, hur.nc,...) in BoundaryFiles section below. 
    4451ok_guide=n 
    4552 
  • CONFIG/UNIFORM/v5/LMDZOR_v5/EXPERIMENTS/LMDZOR/clim/COMP/lmdz.card

    r1750 r1787  
    99# NPv3.1 for new physics, to be used with LMDZ5/trunk revision 1554 or later 
    1010LMDZ_Physics=AP 
    11 #LMDZ_Physics=NPv3.1 
    12  
    13 # You can choose here the name of create_etat0 you want to use 
    14 # If noting is defined here, the job will get the JobName in the file  ../CREATE/config.card 
     11 
     12# Set the variable CREATE needed further below to find the initial and boundary condition files. 
    1513CREATE=ELC-${RESOL_ATM_3D} 
     14 
     15# ByPass_hgardfou_teta=y : modify teta_ parameters for following CumulPeriod only 
    1616ByPass_hgardfou_teta=n 
     17 
     18# ByPass_hgardfou_mats=y : set parameter purmats=y for following CumulPeriod only 
    1719ByPass_hgardfou_mats=n 
     20 
     21# Number of periods where to set parameter adjust=y before switching to adjust=n 
     22# For adjust=n, set LMDZ_NbPeriod_ajust=0.  
    1823LMDZ_NbPeriod_adjust=3 
    19 # LMDZ_NbPeriod_adjust=0 
    20 # To force usage of this Bands file, put LMDZ_NbPeriod_adjust=0 and replace XXXXXXX by Restart Job Name 
     24 
     25# To force usage of specific Bands file, set LMDZ_NbPeriod_adjust=0 and replace XXXXXXX by Restart Job Name 
    2126# LMDZ_Bands_file_name=${ARCHIVE}/IGCM_OUT/IPSLCM5/XXXXXXX/ATM/Debug/XXXXXXX_Bands_96x95x19_3prc.dat_3 
    2227 
     
    4247 
    4348# Nugding : ok_guide=y/n 
     49# If ok_guide=y, add nudging files(u.nc, v.nc, hur.nc,...) in BoundaryFiles section below. 
    4450ok_guide=n 
     51 
    4552 
    4653[InitialStateFiles] 
Note: See TracChangeset for help on using the changeset viewer.