[12983] | 1 | MODULE sbcice_cice |
---|
| 2 | !!====================================================================== |
---|
| 3 | !! *** MODULE sbcice_cice *** |
---|
| 4 | !! To couple with sea ice model CICE (LANL) |
---|
| 5 | !!===================================================================== |
---|
| 6 | #if defined key_cice |
---|
| 7 | !!---------------------------------------------------------------------- |
---|
| 8 | !! 'key_cice' : CICE sea-ice model |
---|
| 9 | !!---------------------------------------------------------------------- |
---|
| 10 | !! sbc_ice_cice : sea-ice model time-stepping and update ocean sbc over ice-covered area |
---|
| 11 | !!---------------------------------------------------------------------- |
---|
| 12 | USE oce ! ocean dynamics and tracers |
---|
| 13 | USE dom_oce ! ocean space and time domain |
---|
| 14 | !!st8 |
---|
| 15 | # if ! defined key_qco |
---|
| 16 | USE domvvl |
---|
| 17 | # else |
---|
| 18 | USE domqco |
---|
| 19 | # endif |
---|
| 20 | !!st8 |
---|
| 21 | USE phycst, only : rcp, rho0, r1_rho0, rhos, rhoi |
---|
| 22 | USE in_out_manager ! I/O manager |
---|
| 23 | USE iom, ONLY : iom_put,iom_use ! I/O manager library !!Joakim edit |
---|
| 24 | USE lib_mpp ! distributed memory computing library |
---|
| 25 | USE lbclnk ! ocean lateral boundary conditions (or mpp link) |
---|
| 26 | USE daymod ! calendar |
---|
| 27 | USE fldread ! read input fields |
---|
| 28 | USE sbc_oce ! Surface boundary condition: ocean fields |
---|
| 29 | USE sbc_ice ! Surface boundary condition: ice fields |
---|
| 30 | USE sbcblk ! Surface boundary condition: bulk |
---|
| 31 | USE sbccpl |
---|
| 32 | |
---|
| 33 | USE ice_kinds_mod |
---|
| 34 | USE ice_blocks |
---|
| 35 | USE ice_domain |
---|
| 36 | USE ice_domain_size |
---|
| 37 | USE ice_boundary |
---|
| 38 | USE ice_constants |
---|
| 39 | USE ice_gather_scatter |
---|
| 40 | USE ice_calendar, only: dt |
---|
| 41 | USE ice_state, only: aice,aicen,uvel,vvel,vsno,vsnon,vice,vicen |
---|
| 42 | # if defined key_cice4 |
---|
| 43 | USE ice_flux, only: strax,stray,strocnx,strocny,frain,fsnow, & |
---|
| 44 | strocnxT,strocnyT, & |
---|
| 45 | sst,sss,uocn,vocn,ss_tltx,ss_tlty,fsalt_gbm, & |
---|
| 46 | fresh_gbm,fhocn_gbm,fswthru_gbm,frzmlt, & |
---|
| 47 | flatn_f,fsurfn_f,fcondtopn_f, & |
---|
| 48 | uatm,vatm,wind,fsw,flw,Tair,potT,Qa,rhoa,zlvl, & |
---|
| 49 | swvdr,swvdf,swidr,swidf |
---|
| 50 | USE ice_therm_vertical, only: calc_Tsfc |
---|
| 51 | #else |
---|
| 52 | USE ice_flux, only: strax,stray,strocnx,strocny,frain,fsnow, & |
---|
| 53 | strocnxT,strocnyT, & |
---|
| 54 | sst,sss,uocn,vocn,ss_tltx,ss_tlty,fsalt_ai, & |
---|
| 55 | fresh_ai,fhocn_ai,fswthru_ai,frzmlt, & |
---|
| 56 | flatn_f,fsurfn_f,fcondtopn_f, & |
---|
| 57 | uatm,vatm,wind,fsw,flw,Tair,potT,Qa,rhoa,zlvl, & |
---|
| 58 | swvdr,swvdf,swidr,swidf |
---|
| 59 | USE ice_therm_shared, only: calc_Tsfc |
---|
| 60 | #endif |
---|
| 61 | USE ice_forcing, only: frcvdr,frcvdf,frcidr,frcidf |
---|
| 62 | USE ice_atmo, only: calc_strair |
---|
| 63 | |
---|
| 64 | USE CICE_InitMod |
---|
| 65 | USE CICE_RunMod |
---|
| 66 | USE CICE_FinalMod |
---|
| 67 | |
---|
| 68 | IMPLICIT NONE |
---|
| 69 | PRIVATE |
---|
| 70 | |
---|
| 71 | PUBLIC cice_sbc_init ! routine called by sbc_init |
---|
| 72 | PUBLIC cice_sbc_final ! routine called by sbc_final |
---|
| 73 | PUBLIC sbc_ice_cice ! routine called by sbc |
---|
| 74 | |
---|
| 75 | INTEGER :: ji_off |
---|
| 76 | INTEGER :: jj_off |
---|
| 77 | |
---|
| 78 | INTEGER , PARAMETER :: jpfld = 13 ! maximum number of files to read |
---|
| 79 | INTEGER , PARAMETER :: jp_snow = 1 ! index of snow file |
---|
| 80 | INTEGER , PARAMETER :: jp_rain = 2 ! index of rain file |
---|
| 81 | INTEGER , PARAMETER :: jp_sblm = 3 ! index of sublimation file |
---|
| 82 | INTEGER , PARAMETER :: jp_top1 = 4 ! index of category 1 topmelt file |
---|
| 83 | INTEGER , PARAMETER :: jp_top2 = 5 ! index of category 2 topmelt file |
---|
| 84 | INTEGER , PARAMETER :: jp_top3 = 6 ! index of category 3 topmelt file |
---|
| 85 | INTEGER , PARAMETER :: jp_top4 = 7 ! index of category 4 topmelt file |
---|
| 86 | INTEGER , PARAMETER :: jp_top5 = 8 ! index of category 5 topmelt file |
---|
| 87 | INTEGER , PARAMETER :: jp_bot1 = 9 ! index of category 1 botmelt file |
---|
| 88 | INTEGER , PARAMETER :: jp_bot2 = 10 ! index of category 2 botmelt file |
---|
| 89 | INTEGER , PARAMETER :: jp_bot3 = 11 ! index of category 3 botmelt file |
---|
| 90 | INTEGER , PARAMETER :: jp_bot4 = 12 ! index of category 4 botmelt file |
---|
| 91 | INTEGER , PARAMETER :: jp_bot5 = 13 ! index of category 5 botmelt file |
---|
| 92 | TYPE(FLD), ALLOCATABLE, DIMENSION(:) :: sf ! structure of input fields (file informations, fields read) |
---|
| 93 | |
---|
| 94 | REAL(wp), ALLOCATABLE, SAVE, DIMENSION(:,:,:), PRIVATE :: png ! local array used in sbc_cice_ice |
---|
| 95 | |
---|
| 96 | !! * Substitutions |
---|
| 97 | # include "do_loop_substitute.h90" |
---|
| 98 | !!---------------------------------------------------------------------- |
---|
| 99 | !! NEMO/OCE 4.0 , NEMO Consortium (2018) |
---|
| 100 | !! $Id: sbcice_cice.F90 12614 2020-03-26 14:59:52Z gm $ |
---|
| 101 | !! Software governed by the CeCILL license (see ./LICENSE) |
---|
| 102 | !!---------------------------------------------------------------------- |
---|
| 103 | CONTAINS |
---|
| 104 | |
---|
| 105 | INTEGER FUNCTION sbc_ice_cice_alloc() |
---|
| 106 | !!---------------------------------------------------------------------- |
---|
| 107 | !! *** FUNCTION sbc_ice_cice_alloc *** |
---|
| 108 | !!---------------------------------------------------------------------- |
---|
| 109 | ALLOCATE( png(jpi,jpj,jpnij), STAT=sbc_ice_cice_alloc ) |
---|
| 110 | CALL mpp_sum ( 'sbcice_cice', sbc_ice_cice_alloc ) |
---|
| 111 | IF( sbc_ice_cice_alloc > 0 ) CALL ctl_warn('sbc_ice_cice_alloc: allocation of arrays failed.') |
---|
| 112 | END FUNCTION sbc_ice_cice_alloc |
---|
| 113 | |
---|
| 114 | SUBROUTINE sbc_ice_cice( kt, ksbc ) |
---|
| 115 | !!--------------------------------------------------------------------- |
---|
| 116 | !! *** ROUTINE sbc_ice_cice *** |
---|
| 117 | !! |
---|
| 118 | !! ** Purpose : update the ocean surface boundary condition via the |
---|
| 119 | !! CICE Sea Ice Model time stepping |
---|
| 120 | !! |
---|
| 121 | !! ** Method : - Get any extra forcing fields for CICE |
---|
| 122 | !! - Prepare forcing fields |
---|
| 123 | !! - CICE model time stepping |
---|
| 124 | !! - call the routine that computes mass and |
---|
| 125 | !! heat fluxes at the ice/ocean interface |
---|
| 126 | !! |
---|
| 127 | !! ** Action : - time evolution of the CICE sea-ice model |
---|
| 128 | !! - update all sbc variables below sea-ice: |
---|
| 129 | !! utau, vtau, qns , qsr, emp , sfx |
---|
| 130 | !!--------------------------------------------------------------------- |
---|
| 131 | INTEGER, INTENT(in) :: kt ! ocean time step |
---|
| 132 | INTEGER, INTENT(in) :: ksbc ! surface forcing type |
---|
| 133 | !!---------------------------------------------------------------------- |
---|
| 134 | ! |
---|
| 135 | ! !----------------------! |
---|
| 136 | IF( MOD( kt-1, nn_fsbc ) == 0 ) THEN ! Ice time-step only ! |
---|
| 137 | ! !----------------------! |
---|
| 138 | |
---|
| 139 | ! Make sure any fluxes required for CICE are set |
---|
| 140 | IF ( ksbc == jp_flx ) THEN |
---|
| 141 | CALL cice_sbc_force(kt) |
---|
| 142 | ELSE IF( ksbc == jp_purecpl ) THEN |
---|
| 143 | CALL sbc_cpl_ice_flx( fr_i ) |
---|
| 144 | ENDIF |
---|
| 145 | |
---|
| 146 | CALL cice_sbc_in ( kt, ksbc ) |
---|
| 147 | CALL CICE_Run |
---|
| 148 | CALL cice_sbc_out ( kt, ksbc ) |
---|
| 149 | |
---|
| 150 | IF( ksbc == jp_purecpl ) CALL cice_sbc_hadgam(kt+1) |
---|
| 151 | |
---|
| 152 | ENDIF ! End sea-ice time step only |
---|
| 153 | ! |
---|
| 154 | END SUBROUTINE sbc_ice_cice |
---|
| 155 | |
---|
| 156 | |
---|
| 157 | SUBROUTINE cice_sbc_init( ksbc, Kbb, Kmm ) |
---|
| 158 | !!--------------------------------------------------------------------- |
---|
| 159 | !! *** ROUTINE cice_sbc_init *** |
---|
| 160 | !! ** Purpose: Initialise ice related fields for NEMO and coupling |
---|
| 161 | !! |
---|
| 162 | !!--------------------------------------------------------------------- |
---|
| 163 | INTEGER, INTENT( in ) :: ksbc ! surface forcing type |
---|
| 164 | INTEGER, INTENT( in ) :: Kbb, Kmm ! time level indices |
---|
| 165 | REAL(wp), DIMENSION(jpi,jpj) :: ztmp1, ztmp2 |
---|
| 166 | REAL(wp) :: zcoefu, zcoefv, zcoeff ! local scalar |
---|
| 167 | INTEGER :: ji, jj, jl, jk ! dummy loop indices |
---|
| 168 | !!--------------------------------------------------------------------- |
---|
| 169 | ! |
---|
| 170 | IF(lwp) WRITE(numout,*)'cice_sbc_init' |
---|
| 171 | |
---|
| 172 | ji_off = INT ( (jpiglo - nx_global) / 2 ) |
---|
| 173 | jj_off = INT ( (jpjglo - ny_global) / 2 ) |
---|
| 174 | |
---|
| 175 | #if defined key_nemocice_decomp |
---|
| 176 | ! Pass initial SST from NEMO to CICE so ice is initialised correctly if |
---|
| 177 | ! there is no restart file. |
---|
| 178 | ! Values from a CICE restart file would overwrite this |
---|
| 179 | IF( .NOT. ln_rstart ) THEN |
---|
| 180 | CALL nemo2cice( ts(:,:,1,jp_tem,Kmm) , sst , 'T' , 1.) |
---|
| 181 | ENDIF |
---|
| 182 | #endif |
---|
| 183 | |
---|
| 184 | ! Initialize CICE |
---|
| 185 | CALL CICE_Initialize |
---|
| 186 | |
---|
| 187 | ! Do some CICE consistency checks |
---|
| 188 | IF( (ksbc == jp_flx) .OR. (ksbc == jp_purecpl) ) THEN |
---|
| 189 | IF( calc_strair .OR. calc_Tsfc ) THEN |
---|
| 190 | CALL ctl_stop( 'STOP', 'cice_sbc_init : Forcing option requires calc_strair=F and calc_Tsfc=F in ice_in' ) |
---|
| 191 | ENDIF |
---|
| 192 | ELSEIF(ksbc == jp_blk) THEN |
---|
| 193 | IF( .NOT. (calc_strair .AND. calc_Tsfc) ) THEN |
---|
| 194 | CALL ctl_stop( 'STOP', 'cice_sbc_init : Forcing option requires calc_strair=T and calc_Tsfc=T in ice_in' ) |
---|
| 195 | ENDIF |
---|
| 196 | ENDIF |
---|
| 197 | |
---|
| 198 | |
---|
| 199 | ! allocate sbc_ice and sbc_cice arrays |
---|
| 200 | IF( sbc_ice_alloc() /= 0 ) CALL ctl_stop( 'STOP', 'sbc_ice_cice_alloc : unable to allocate arrays' ) |
---|
| 201 | IF( sbc_ice_cice_alloc() /= 0 ) CALL ctl_stop( 'STOP', 'sbc_ice_cice_alloc : unable to allocate cice arrays' ) |
---|
| 202 | |
---|
| 203 | ! Ensure ocean temperatures are nowhere below freezing if not a NEMO restart |
---|
| 204 | IF( .NOT. ln_rstart ) THEN |
---|
| 205 | ts(:,:,:,jp_tem,Kmm) = MAX (ts(:,:,:,jp_tem,Kmm),Tocnfrz) |
---|
| 206 | ts(:,:,:,jp_tem,Kbb) = ts(:,:,:,jp_tem,Kmm) |
---|
| 207 | ENDIF |
---|
| 208 | |
---|
| 209 | fr_iu(:,:)=0.0 |
---|
| 210 | fr_iv(:,:)=0.0 |
---|
| 211 | |
---|
| 212 | CALL cice2nemo(aice,fr_i, 'T', 1. ) |
---|
| 213 | IF( (ksbc == jp_flx) .OR. (ksbc == jp_purecpl) ) THEN |
---|
| 214 | DO jl=1,ncat |
---|
| 215 | CALL cice2nemo(aicen(:,:,jl,:),a_i(:,:,jl), 'T', 1. ) |
---|
| 216 | ENDDO |
---|
| 217 | ENDIF |
---|
| 218 | |
---|
| 219 | ! T point to U point |
---|
| 220 | ! T point to V point |
---|
[13295] | 221 | DO_2D( 1, 0, 1, 0 ) |
---|
[12983] | 222 | fr_iu(ji,jj)=0.5*(fr_i(ji,jj)+fr_i(ji+1,jj))*umask(ji,jj,1) |
---|
| 223 | fr_iv(ji,jj)=0.5*(fr_i(ji,jj)+fr_i(ji,jj+1))*vmask(ji,jj,1) |
---|
| 224 | END_2D |
---|
| 225 | |
---|
| 226 | CALL lbc_lnk_multi( 'sbcice_cice', fr_iu , 'U', 1., fr_iv , 'V', 1. ) |
---|
| 227 | |
---|
| 228 | ! set the snow+ice mass |
---|
| 229 | CALL cice2nemo(vsno(:,:,:),ztmp1,'T', 1. ) |
---|
| 230 | CALL cice2nemo(vice(:,:,:),ztmp2,'T', 1. ) |
---|
| 231 | snwice_mass (:,:) = ( rhos * ztmp1(:,:) + rhoi * ztmp2(:,:) ) |
---|
| 232 | snwice_mass_b(:,:) = snwice_mass(:,:) |
---|
| 233 | |
---|
| 234 | IF( .NOT.ln_rstart ) THEN |
---|
| 235 | IF( ln_ice_embd ) THEN ! embedded sea-ice: deplete the initial ssh below sea-ice area |
---|
| 236 | ssh(:,:,Kmm) = ssh(:,:,Kmm) - snwice_mass(:,:) * r1_rho0 |
---|
| 237 | ssh(:,:,Kbb) = ssh(:,:,Kbb) - snwice_mass(:,:) * r1_rho0 |
---|
| 238 | |
---|
| 239 | !!gm This should be put elsewhere.... (same remark for limsbc) |
---|
| 240 | !!gm especially here it is assumed zstar coordinate, but it can be ztilde.... |
---|
| 241 | !!st9 |
---|
| 242 | #if defined key_qco |
---|
| 243 | IF( .NOT.ln_linssh ) CALL dom_qco_zgr( Kbb, Kmm, Kaa ) ! interpolation scale factor, depth and water column |
---|
| 244 | #else |
---|
| 245 | IF( .NOT.ln_linssh ) THEN |
---|
| 246 | ! |
---|
| 247 | DO jk = 1,jpkm1 ! adjust initial vertical scale factors |
---|
| 248 | e3t(:,:,jk,Kmm) = e3t_0(:,:,jk)*( 1._wp + ssh(:,:,Kmm)*r1_ht_0(:,:)*tmask(:,:,jk) ) |
---|
| 249 | e3t(:,:,jk,Kbb) = e3t_0(:,:,jk)*( 1._wp + ssh(:,:,Kbb)*r1_ht_0(:,:)*tmask(:,:,jk) ) |
---|
| 250 | END DO |
---|
| 251 | e3t(:,:,:,Krhs) = e3t(:,:,:,Kbb) |
---|
| 252 | ! Reconstruction of all vertical scale factors at now and before time-steps |
---|
| 253 | ! ============================================================================= |
---|
| 254 | ! Horizontal scale factor interpolations |
---|
| 255 | ! -------------------------------------- |
---|
| 256 | CALL dom_vvl_interpol( ssh(:,:,Kbb), e3u(:,:,:,Kbb), 'U' ) |
---|
| 257 | CALL dom_vvl_interpol( ssh(:,:,Kbb), e3v(:,:,:,Kbb), 'V' ) |
---|
| 258 | CALL dom_vvl_interpol( ssh(:,:,Kmm), e3u(:,:,:,Kmm), 'U' ) |
---|
| 259 | CALL dom_vvl_interpol( ssh(:,:,Kmm), e3v(:,:,:,Kmm), 'V' ) |
---|
| 260 | CALL dom_vvl_interpol( ssh(:,:,Kmm), e3f(:,:,:), 'F' ) |
---|
| 261 | ! Vertical scale factor interpolations |
---|
| 262 | ! ------------------------------------ |
---|
| 263 | CALL dom_vvl_interpol( ssh(:,:,Kmm), e3w (:,:,:,Kmm), 'W' ) |
---|
| 264 | CALL dom_vvl_interpol( ssh(:,:,Kmm), e3uw(:,:,:,Kmm), 'UW' ) |
---|
| 265 | CALL dom_vvl_interpol( ssh(:,:,Kmm), e3vw(:,:,:,Kmm), 'VW' ) |
---|
| 266 | CALL dom_vvl_interpol( ssh(:,:,Kbb), e3uw(:,:,:,Kbb), 'UW' ) |
---|
| 267 | CALL dom_vvl_interpol( ssh(:,:,Kbb), e3vw(:,:,:,Kbb), 'VW' ) |
---|
| 268 | ! t- and w- points depth |
---|
| 269 | ! ---------------------- |
---|
| 270 | gdept(:,:,1,Kmm) = 0.5_wp * e3w(:,:,1,Kmm) |
---|
| 271 | gdepw(:,:,1,Kmm) = 0.0_wp |
---|
| 272 | gde3w(:,:,1) = gdept(:,:,1,Kmm) - ssh(:,:,Kmm) |
---|
| 273 | DO jk = 2, jpk |
---|
| 274 | gdept(:,:,jk,Kmm) = gdept(:,:,jk-1,Kmm) + e3w(:,:,jk,Kmm) |
---|
| 275 | gdepw(:,:,jk,Kmm) = gdepw(:,:,jk-1,Kmm) + e3t(:,:,jk-1,Kmm) |
---|
| 276 | gde3w(:,:,jk) = gdept(:,:,jk ,Kmm) - sshn (:,:) |
---|
| 277 | END DO |
---|
| 278 | ENDIF |
---|
| 279 | #endif |
---|
| 280 | !!st9 |
---|
| 281 | ENDIF |
---|
| 282 | ENDIF |
---|
| 283 | ! |
---|
| 284 | END SUBROUTINE cice_sbc_init |
---|
| 285 | |
---|
| 286 | |
---|
| 287 | SUBROUTINE cice_sbc_in( kt, ksbc ) |
---|
| 288 | !!--------------------------------------------------------------------- |
---|
| 289 | !! *** ROUTINE cice_sbc_in *** |
---|
| 290 | !! ** Purpose: Set coupling fields and pass to CICE |
---|
| 291 | !!--------------------------------------------------------------------- |
---|
| 292 | INTEGER, INTENT(in ) :: kt ! ocean time step |
---|
| 293 | INTEGER, INTENT(in ) :: ksbc ! surface forcing type |
---|
| 294 | ! |
---|
| 295 | INTEGER :: ji, jj, jl ! dummy loop indices |
---|
| 296 | REAL(wp), DIMENSION(jpi,jpj) :: ztmp, zpice |
---|
| 297 | REAL(wp), DIMENSION(jpi,jpj,ncat) :: ztmpn |
---|
| 298 | REAL(wp) :: zintb, zintn ! dummy argument |
---|
| 299 | !!--------------------------------------------------------------------- |
---|
| 300 | ! |
---|
| 301 | IF( kt == nit000 ) THEN |
---|
| 302 | IF(lwp) WRITE(numout,*)'cice_sbc_in' |
---|
| 303 | ENDIF |
---|
| 304 | |
---|
| 305 | ztmp(:,:)=0.0 |
---|
| 306 | |
---|
| 307 | ! Aggregate ice concentration already set in cice_sbc_out (or cice_sbc_init on |
---|
| 308 | ! the first time-step) |
---|
| 309 | |
---|
| 310 | ! forced and coupled case |
---|
| 311 | |
---|
| 312 | IF( (ksbc == jp_flx).OR.(ksbc == jp_purecpl) ) THEN |
---|
| 313 | |
---|
| 314 | ztmpn(:,:,:)=0.0 |
---|
| 315 | |
---|
| 316 | ! x comp of wind stress (CI_1) |
---|
| 317 | ! U point to F point |
---|
[13295] | 318 | DO_2D( 1, 0, 1, 1 ) |
---|
[12983] | 319 | ztmp(ji,jj) = 0.5 * ( fr_iu(ji,jj) * utau(ji,jj) & |
---|
| 320 | + fr_iu(ji,jj+1) * utau(ji,jj+1) ) * fmask(ji,jj,1) |
---|
| 321 | END_2D |
---|
| 322 | CALL nemo2cice(ztmp,strax,'F', -1. ) |
---|
| 323 | |
---|
| 324 | ! y comp of wind stress (CI_2) |
---|
| 325 | ! V point to F point |
---|
[13295] | 326 | DO_2D( 1, 1, 1, 0 ) |
---|
[12983] | 327 | ztmp(ji,jj) = 0.5 * ( fr_iv(ji,jj) * vtau(ji,jj) & |
---|
| 328 | + fr_iv(ji+1,jj) * vtau(ji+1,jj) ) * fmask(ji,jj,1) |
---|
| 329 | END_2D |
---|
| 330 | CALL nemo2cice(ztmp,stray,'F', -1. ) |
---|
| 331 | |
---|
| 332 | ! Surface downward latent heat flux (CI_5) |
---|
| 333 | IF(ksbc == jp_flx) THEN |
---|
| 334 | DO jl=1,ncat |
---|
| 335 | ztmpn(:,:,jl)=qla_ice(:,:,1)*a_i(:,:,jl) |
---|
| 336 | ENDDO |
---|
| 337 | ELSE |
---|
| 338 | ! emp_ice is set in sbc_cpl_ice_flx as sublimation-snow |
---|
| 339 | qla_ice(:,:,1)= - ( emp_ice(:,:)+sprecip(:,:) ) * rLsub |
---|
| 340 | ! End of temporary code |
---|
[13295] | 341 | DO_2D( 1, 1, 1, 1 ) |
---|
[12983] | 342 | IF(fr_i(ji,jj).eq.0.0) THEN |
---|
| 343 | DO jl=1,ncat |
---|
| 344 | ztmpn(ji,jj,jl)=0.0 |
---|
| 345 | ENDDO |
---|
| 346 | ! This will then be conserved in CICE |
---|
| 347 | ztmpn(ji,jj,1)=qla_ice(ji,jj,1) |
---|
| 348 | ELSE |
---|
| 349 | DO jl=1,ncat |
---|
| 350 | ztmpn(ji,jj,jl)=qla_ice(ji,jj,1)*a_i(ji,jj,jl)/fr_i(ji,jj) |
---|
| 351 | ENDDO |
---|
| 352 | ENDIF |
---|
| 353 | END_2D |
---|
| 354 | ENDIF |
---|
| 355 | DO jl=1,ncat |
---|
| 356 | CALL nemo2cice(ztmpn(:,:,jl),flatn_f(:,:,jl,:),'T', 1. ) |
---|
| 357 | |
---|
| 358 | ! GBM conductive flux through ice (CI_6) |
---|
| 359 | ! Convert to GBM |
---|
| 360 | IF(ksbc == jp_flx) THEN |
---|
| 361 | ztmp(:,:) = botmelt(:,:,jl)*a_i(:,:,jl) |
---|
| 362 | ELSE |
---|
| 363 | ztmp(:,:) = botmelt(:,:,jl) |
---|
| 364 | ENDIF |
---|
| 365 | CALL nemo2cice(ztmp,fcondtopn_f(:,:,jl,:),'T', 1. ) |
---|
| 366 | |
---|
| 367 | ! GBM surface heat flux (CI_7) |
---|
| 368 | ! Convert to GBM |
---|
| 369 | IF(ksbc == jp_flx) THEN |
---|
| 370 | ztmp(:,:) = (topmelt(:,:,jl)+botmelt(:,:,jl))*a_i(:,:,jl) |
---|
| 371 | ELSE |
---|
| 372 | ztmp(:,:) = (topmelt(:,:,jl)+botmelt(:,:,jl)) |
---|
| 373 | ENDIF |
---|
| 374 | CALL nemo2cice(ztmp,fsurfn_f(:,:,jl,:),'T', 1. ) |
---|
| 375 | ENDDO |
---|
| 376 | |
---|
| 377 | ELSE IF(ksbc == jp_blk) THEN |
---|
| 378 | |
---|
| 379 | ! Pass bulk forcing fields to CICE (which will calculate heat fluxes etc itself) |
---|
| 380 | ! x comp and y comp of atmosphere surface wind (CICE expects on T points) |
---|
| 381 | ztmp(:,:) = wndi_ice(:,:) |
---|
| 382 | CALL nemo2cice(ztmp,uatm,'T', -1. ) |
---|
| 383 | ztmp(:,:) = wndj_ice(:,:) |
---|
| 384 | CALL nemo2cice(ztmp,vatm,'T', -1. ) |
---|
| 385 | ztmp(:,:) = SQRT ( wndi_ice(:,:)**2 + wndj_ice(:,:)**2 ) |
---|
| 386 | CALL nemo2cice(ztmp,wind,'T', 1. ) ! Wind speed (m/s) |
---|
| 387 | ztmp(:,:) = qsr_ice(:,:,1) |
---|
| 388 | CALL nemo2cice(ztmp,fsw,'T', 1. ) ! Incoming short-wave (W/m^2) |
---|
| 389 | ztmp(:,:) = qlw_ice(:,:,1) |
---|
| 390 | CALL nemo2cice(ztmp,flw,'T', 1. ) ! Incoming long-wave (W/m^2) |
---|
| 391 | ztmp(:,:) = tatm_ice(:,:) |
---|
| 392 | CALL nemo2cice(ztmp,Tair,'T', 1. ) ! Air temperature (K) |
---|
| 393 | CALL nemo2cice(ztmp,potT,'T', 1. ) ! Potential temp (K) |
---|
| 394 | ! Following line uses MAX(....) to avoid problems if tatm_ice has unset halo rows |
---|
| 395 | ztmp(:,:) = 101000. / ( 287.04 * MAX(1.0,tatm_ice(:,:)) ) |
---|
| 396 | ! Constant (101000.) atm pressure assumed |
---|
| 397 | CALL nemo2cice(ztmp,rhoa,'T', 1. ) ! Air density (kg/m^3) |
---|
| 398 | ztmp(:,:) = qatm_ice(:,:) |
---|
| 399 | CALL nemo2cice(ztmp,Qa,'T', 1. ) ! Specific humidity (kg/kg) |
---|
| 400 | ztmp(:,:)=10.0 |
---|
| 401 | CALL nemo2cice(ztmp,zlvl,'T', 1. ) ! Atmos level height (m) |
---|
| 402 | |
---|
| 403 | ! May want to check all values are physically realistic (as in CICE routine |
---|
| 404 | ! prepare_forcing)? |
---|
| 405 | |
---|
| 406 | ! Divide shortwave into spectral bands (as in prepare_forcing) |
---|
| 407 | ztmp(:,:)=qsr_ice(:,:,1)*frcvdr ! visible direct |
---|
| 408 | CALL nemo2cice(ztmp,swvdr,'T', 1. ) |
---|
| 409 | ztmp(:,:)=qsr_ice(:,:,1)*frcvdf ! visible diffuse |
---|
| 410 | CALL nemo2cice(ztmp,swvdf,'T', 1. ) |
---|
| 411 | ztmp(:,:)=qsr_ice(:,:,1)*frcidr ! near IR direct |
---|
| 412 | CALL nemo2cice(ztmp,swidr,'T', 1. ) |
---|
| 413 | ztmp(:,:)=qsr_ice(:,:,1)*frcidf ! near IR diffuse |
---|
| 414 | CALL nemo2cice(ztmp,swidf,'T', 1. ) |
---|
| 415 | |
---|
| 416 | ENDIF |
---|
| 417 | |
---|
| 418 | ! Snowfall |
---|
| 419 | ! Ensure fsnow is positive (as in CICE routine prepare_forcing) |
---|
| 420 | IF( iom_use('snowpre') ) CALL iom_put('snowpre',MAX( (1.0-fr_i(:,:))*sprecip(:,:) ,0.0)) !!Joakim edit |
---|
| 421 | ztmp(:,:)=MAX(fr_i(:,:)*sprecip(:,:),0.0) |
---|
| 422 | CALL nemo2cice(ztmp,fsnow,'T', 1. ) |
---|
| 423 | |
---|
| 424 | ! Rainfall |
---|
| 425 | IF( iom_use('precip') ) CALL iom_put('precip', (1.0-fr_i(:,:))*(tprecip(:,:)-sprecip(:,:)) ) !!Joakim edit |
---|
| 426 | ztmp(:,:)=fr_i(:,:)*(tprecip(:,:)-sprecip(:,:)) |
---|
| 427 | CALL nemo2cice(ztmp,frain,'T', 1. ) |
---|
| 428 | |
---|
| 429 | ! Freezing/melting potential |
---|
| 430 | ! Calculated over NEMO leapfrog timestep (hence 2*dt) |
---|
| 431 | nfrzmlt(:,:) = rho0 * rcp * e3t_m(:,:) * ( Tocnfrz-sst_m(:,:) ) / ( 2.0*dt ) |
---|
| 432 | |
---|
| 433 | ztmp(:,:) = nfrzmlt(:,:) |
---|
| 434 | CALL nemo2cice(ztmp,frzmlt,'T', 1. ) |
---|
| 435 | |
---|
| 436 | ! SST and SSS |
---|
| 437 | |
---|
| 438 | CALL nemo2cice(sst_m,sst,'T', 1. ) |
---|
| 439 | CALL nemo2cice(sss_m,sss,'T', 1. ) |
---|
| 440 | |
---|
| 441 | ! x comp and y comp of surface ocean current |
---|
| 442 | ! U point to F point |
---|
[13295] | 443 | DO_2D( 1, 0, 1, 1 ) |
---|
[12983] | 444 | ztmp(ji,jj)=0.5*(ssu_m(ji,jj)+ssu_m(ji,jj+1))*fmask(ji,jj,1) |
---|
| 445 | END_2D |
---|
| 446 | CALL nemo2cice(ztmp,uocn,'F', -1. ) |
---|
| 447 | |
---|
| 448 | ! V point to F point |
---|
[13295] | 449 | DO_2D( 1, 1, 1, 0 ) |
---|
[12983] | 450 | ztmp(ji,jj)=0.5*(ssv_m(ji,jj)+ssv_m(ji+1,jj))*fmask(ji,jj,1) |
---|
| 451 | END_2D |
---|
| 452 | CALL nemo2cice(ztmp,vocn,'F', -1. ) |
---|
| 453 | |
---|
| 454 | IF( ln_ice_embd ) THEN !== embedded sea ice: compute representative ice top surface ==! |
---|
| 455 | ! |
---|
| 456 | ! average interpolation coeff as used in dynspg = (1/nn_fsbc) * {SUM[n/nn_fsbc], n=0,nn_fsbc-1} |
---|
| 457 | ! = (1/nn_fsbc)^2 * {SUM[n], n=0,nn_fsbc-1} |
---|
| 458 | zintn = REAL( nn_fsbc - 1 ) / REAL( nn_fsbc ) * 0.5_wp |
---|
| 459 | ! |
---|
| 460 | ! average interpolation coeff as used in dynspg = (1/nn_fsbc) * {SUM[1-n/nn_fsbc], n=0,nn_fsbc-1} |
---|
| 461 | ! = (1/nn_fsbc)^2 * (nn_fsbc^2 - {SUM[n], n=0,nn_fsbc-1}) |
---|
| 462 | zintb = REAL( nn_fsbc + 1 ) / REAL( nn_fsbc ) * 0.5_wp |
---|
| 463 | ! |
---|
| 464 | zpice(:,:) = ssh_m(:,:) + ( zintn * snwice_mass(:,:) + zintb * snwice_mass_b(:,:) ) * r1_rho0 |
---|
| 465 | ! |
---|
| 466 | ! |
---|
| 467 | ELSE !== non-embedded sea ice: use ocean surface for slope calculation ==! |
---|
| 468 | zpice(:,:) = ssh_m(:,:) |
---|
| 469 | ENDIF |
---|
| 470 | |
---|
| 471 | ! x comp and y comp of sea surface slope (on F points) |
---|
| 472 | ! T point to F point |
---|
[13295] | 473 | DO_2D( 1, 0, 1, 0 ) |
---|
[12983] | 474 | ztmp(ji,jj)=0.5 * ( (zpice(ji+1,jj )-zpice(ji,jj )) * r1_e1u(ji,jj ) & |
---|
| 475 | & + (zpice(ji+1,jj+1)-zpice(ji,jj+1)) * r1_e1u(ji,jj+1) ) * fmask(ji,jj,1) |
---|
| 476 | END_2D |
---|
| 477 | CALL nemo2cice( ztmp,ss_tltx,'F', -1. ) |
---|
| 478 | |
---|
| 479 | ! T point to F point |
---|
[13295] | 480 | DO_2D( 1, 0, 1, 0 ) |
---|
[12983] | 481 | ztmp(ji,jj)=0.5 * ( (zpice(ji ,jj+1)-zpice(ji ,jj)) * r1_e2v(ji ,jj) & |
---|
| 482 | & + (zpice(ji+1,jj+1)-zpice(ji+1,jj)) * r1_e2v(ji+1,jj) ) * fmask(ji,jj,1) |
---|
| 483 | END_2D |
---|
| 484 | CALL nemo2cice(ztmp,ss_tlty,'F', -1. ) |
---|
| 485 | ! |
---|
| 486 | END SUBROUTINE cice_sbc_in |
---|
| 487 | |
---|
| 488 | |
---|
| 489 | SUBROUTINE cice_sbc_out( kt, ksbc ) |
---|
| 490 | !!--------------------------------------------------------------------- |
---|
| 491 | !! *** ROUTINE cice_sbc_out *** |
---|
| 492 | !! ** Purpose: Get fields from CICE and set surface fields for NEMO |
---|
| 493 | !!--------------------------------------------------------------------- |
---|
| 494 | INTEGER, INTENT( in ) :: kt ! ocean time step |
---|
| 495 | INTEGER, INTENT( in ) :: ksbc ! surface forcing type |
---|
| 496 | |
---|
| 497 | INTEGER :: ji, jj, jl ! dummy loop indices |
---|
| 498 | REAL(wp), DIMENSION(jpi,jpj) :: ztmp1, ztmp2 |
---|
| 499 | !!--------------------------------------------------------------------- |
---|
| 500 | ! |
---|
| 501 | IF( kt == nit000 ) THEN |
---|
| 502 | IF(lwp) WRITE(numout,*)'cice_sbc_out' |
---|
| 503 | ENDIF |
---|
| 504 | |
---|
| 505 | ! x comp of ocean-ice stress |
---|
| 506 | CALL cice2nemo(strocnx,ztmp1,'F', -1. ) |
---|
| 507 | ss_iou(:,:)=0.0 |
---|
| 508 | ! F point to U point |
---|
[13295] | 509 | DO_2D( 0, 0, 0, 0 ) |
---|
[12983] | 510 | ss_iou(ji,jj) = 0.5 * ( ztmp1(ji,jj-1) + ztmp1(ji,jj) ) * umask(ji,jj,1) |
---|
| 511 | END_2D |
---|
| 512 | CALL lbc_lnk( 'sbcice_cice', ss_iou , 'U', -1. ) |
---|
| 513 | |
---|
| 514 | ! y comp of ocean-ice stress |
---|
| 515 | CALL cice2nemo(strocny,ztmp1,'F', -1. ) |
---|
| 516 | ss_iov(:,:)=0.0 |
---|
| 517 | ! F point to V point |
---|
| 518 | |
---|
[13295] | 519 | DO_2D( 1, 0, 0, 0 ) |
---|
[12983] | 520 | ss_iov(ji,jj) = 0.5 * ( ztmp1(ji-1,jj) + ztmp1(ji,jj) ) * vmask(ji,jj,1) |
---|
| 521 | END_2D |
---|
| 522 | CALL lbc_lnk( 'sbcice_cice', ss_iov , 'V', -1. ) |
---|
| 523 | |
---|
| 524 | ! x and y comps of surface stress |
---|
| 525 | ! Combine wind stress and ocean-ice stress |
---|
| 526 | ! [Note that fr_iu hasn't yet been updated, so still from start of CICE timestep] |
---|
| 527 | ! strocnx and strocny already weighted by ice fraction in CICE so not done here |
---|
| 528 | |
---|
| 529 | utau(:,:)=(1.0-fr_iu(:,:))*utau(:,:)-ss_iou(:,:) |
---|
| 530 | vtau(:,:)=(1.0-fr_iv(:,:))*vtau(:,:)-ss_iov(:,:) |
---|
| 531 | |
---|
| 532 | ! Also need ice/ocean stress on T points so that taum can be updated |
---|
| 533 | ! This interpolation is already done in CICE so best to use those values |
---|
| 534 | CALL cice2nemo(strocnxT,ztmp1,'T',-1.) |
---|
| 535 | CALL cice2nemo(strocnyT,ztmp2,'T',-1.) |
---|
| 536 | |
---|
| 537 | ! Update taum with modulus of ice-ocean stress |
---|
| 538 | ! strocnxT and strocnyT are not weighted by ice fraction in CICE so must be done here |
---|
| 539 | taum(:,:)=(1.0-fr_i(:,:))*taum(:,:)+fr_i(:,:)*SQRT(ztmp1*ztmp1 + ztmp2*ztmp2) |
---|
| 540 | |
---|
| 541 | ! Freshwater fluxes |
---|
| 542 | |
---|
| 543 | IF(ksbc == jp_flx) THEN |
---|
| 544 | ! Note that emp from the forcing files is evap*(1-aice)-(tprecip-aice*sprecip) |
---|
| 545 | ! What we want here is evap*(1-aice)-tprecip*(1-aice) hence manipulation below |
---|
| 546 | ! Not ideal since aice won't be the same as in the atmosphere. |
---|
| 547 | ! Better to use evap and tprecip? (but for now don't read in evap in this case) |
---|
| 548 | emp(:,:) = emp(:,:)+fr_i(:,:)*(tprecip(:,:)-sprecip(:,:)) |
---|
| 549 | ELSE IF(ksbc == jp_blk) THEN |
---|
| 550 | emp(:,:) = (1.0-fr_i(:,:))*emp(:,:) |
---|
| 551 | ELSE IF(ksbc == jp_purecpl) THEN |
---|
| 552 | ! emp_tot is set in sbc_cpl_ice_flx (called from cice_sbc_in above) |
---|
| 553 | ! This is currently as required with the coupling fields from the UM atmosphere |
---|
| 554 | emp(:,:) = emp_tot(:,:)+tprecip(:,:)*fr_i(:,:) |
---|
| 555 | ENDIF |
---|
| 556 | |
---|
| 557 | #if defined key_cice4 |
---|
| 558 | CALL cice2nemo(fresh_gbm,ztmp1,'T', 1. ) |
---|
| 559 | CALL cice2nemo(fsalt_gbm,ztmp2,'T', 1. ) |
---|
| 560 | #else |
---|
| 561 | CALL cice2nemo(fresh_ai,ztmp1,'T', 1. ) |
---|
| 562 | CALL cice2nemo(fsalt_ai,ztmp2,'T', 1. ) |
---|
| 563 | #endif |
---|
| 564 | |
---|
| 565 | ! Check to avoid unphysical expression when ice is forming (ztmp1 negative) |
---|
| 566 | ! Otherwise we are effectively allowing ice of higher salinity than the ocean to form |
---|
| 567 | ! which has to be compensated for by the ocean salinity potentially going negative |
---|
| 568 | ! This check breaks conservation but seems reasonable until we have prognostic ice salinity |
---|
| 569 | ! Note the 1000.0 below is to convert from kg salt to g salt (needed for PSU) |
---|
| 570 | WHERE (ztmp1(:,:).lt.0.0) ztmp2(:,:)=MAX(ztmp2(:,:),ztmp1(:,:)*sss_m(:,:)/1000.0) |
---|
| 571 | sfx(:,:)=ztmp2(:,:)*1000.0 |
---|
| 572 | emp(:,:)=emp(:,:)-ztmp1(:,:) |
---|
| 573 | fmmflx(:,:) = ztmp1(:,:) !!Joakim edit |
---|
| 574 | |
---|
| 575 | CALL lbc_lnk_multi( 'sbcice_cice', emp , 'T', 1., sfx , 'T', 1. ) |
---|
| 576 | |
---|
| 577 | ! Solar penetrative radiation and non solar surface heat flux |
---|
| 578 | |
---|
| 579 | ! Scale qsr and qns according to ice fraction (bulk formulae only) |
---|
| 580 | |
---|
| 581 | IF(ksbc == jp_blk) THEN |
---|
| 582 | qsr(:,:)=qsr(:,:)*(1.0-fr_i(:,:)) |
---|
| 583 | qns(:,:)=qns(:,:)*(1.0-fr_i(:,:)) |
---|
| 584 | ENDIF |
---|
| 585 | ! Take into account snow melting except for fully coupled when already in qns_tot |
---|
| 586 | IF(ksbc == jp_purecpl) THEN |
---|
| 587 | qsr(:,:)= qsr_tot(:,:) |
---|
| 588 | qns(:,:)= qns_tot(:,:) |
---|
| 589 | ELSE |
---|
| 590 | qns(:,:)= qns(:,:)-sprecip(:,:)*Lfresh*(1.0-fr_i(:,:)) |
---|
| 591 | ENDIF |
---|
| 592 | |
---|
| 593 | ! Now add in ice / snow related terms |
---|
| 594 | ! [fswthru will be zero unless running with calc_Tsfc=T in CICE] |
---|
| 595 | #if defined key_cice4 |
---|
| 596 | CALL cice2nemo(fswthru_gbm,ztmp1,'T', 1. ) |
---|
| 597 | #else |
---|
| 598 | CALL cice2nemo(fswthru_ai,ztmp1,'T', 1. ) |
---|
| 599 | #endif |
---|
| 600 | qsr(:,:)=qsr(:,:)+ztmp1(:,:) |
---|
| 601 | CALL lbc_lnk( 'sbcice_cice', qsr , 'T', 1. ) |
---|
| 602 | |
---|
[13295] | 603 | DO_2D( 1, 1, 1, 1 ) |
---|
[12983] | 604 | nfrzmlt(ji,jj)=MAX(nfrzmlt(ji,jj),0.0) |
---|
| 605 | END_2D |
---|
| 606 | |
---|
| 607 | #if defined key_cice4 |
---|
| 608 | CALL cice2nemo(fhocn_gbm,ztmp1,'T', 1. ) |
---|
| 609 | #else |
---|
| 610 | CALL cice2nemo(fhocn_ai,ztmp1,'T', 1. ) |
---|
| 611 | #endif |
---|
| 612 | qns(:,:)=qns(:,:)+nfrzmlt(:,:)+ztmp1(:,:) |
---|
| 613 | |
---|
| 614 | CALL lbc_lnk( 'sbcice_cice', qns , 'T', 1. ) |
---|
| 615 | |
---|
| 616 | ! Prepare for the following CICE time-step |
---|
| 617 | |
---|
| 618 | CALL cice2nemo(aice,fr_i,'T', 1. ) |
---|
| 619 | IF( (ksbc == jp_flx).OR.(ksbc == jp_purecpl) ) THEN |
---|
| 620 | DO jl=1,ncat |
---|
| 621 | CALL cice2nemo(aicen(:,:,jl,:),a_i(:,:,jl), 'T', 1. ) |
---|
| 622 | ENDDO |
---|
| 623 | ENDIF |
---|
| 624 | |
---|
| 625 | ! T point to U point |
---|
| 626 | ! T point to V point |
---|
[13295] | 627 | DO_2D( 1, 0, 1, 0 ) |
---|
[12983] | 628 | fr_iu(ji,jj)=0.5*(fr_i(ji,jj)+fr_i(ji+1,jj))*umask(ji,jj,1) |
---|
| 629 | fr_iv(ji,jj)=0.5*(fr_i(ji,jj)+fr_i(ji,jj+1))*vmask(ji,jj,1) |
---|
| 630 | END_2D |
---|
| 631 | |
---|
| 632 | CALL lbc_lnk_multi( 'sbcice_cice', fr_iu , 'U', 1., fr_iv , 'V', 1. ) |
---|
| 633 | |
---|
| 634 | ! set the snow+ice mass |
---|
| 635 | CALL cice2nemo(vsno(:,:,:),ztmp1,'T', 1. ) |
---|
| 636 | CALL cice2nemo(vice(:,:,:),ztmp2,'T', 1. ) |
---|
| 637 | snwice_mass (:,:) = ( rhos * ztmp1(:,:) + rhoi * ztmp2(:,:) ) |
---|
| 638 | snwice_mass_b(:,:) = snwice_mass(:,:) |
---|
| 639 | snwice_fmass (:,:) = ( snwice_mass(:,:) - snwice_mass_b(:,:) ) / dt |
---|
| 640 | ! |
---|
| 641 | END SUBROUTINE cice_sbc_out |
---|
| 642 | |
---|
| 643 | |
---|
| 644 | SUBROUTINE cice_sbc_hadgam( kt ) |
---|
| 645 | !!--------------------------------------------------------------------- |
---|
| 646 | !! *** ROUTINE cice_sbc_hadgam *** |
---|
| 647 | !! ** Purpose: Prepare fields needed to pass to HadGAM3 atmosphere |
---|
| 648 | !! |
---|
| 649 | !! |
---|
| 650 | !!--------------------------------------------------------------------- |
---|
| 651 | INTEGER, INTENT( in ) :: kt ! ocean time step |
---|
| 652 | !! |
---|
| 653 | INTEGER :: jl ! dummy loop index |
---|
| 654 | INTEGER :: ierror |
---|
| 655 | !!--------------------------------------------------------------------- |
---|
| 656 | ! |
---|
| 657 | IF( kt == nit000 ) THEN |
---|
| 658 | IF(lwp) WRITE(numout,*)'cice_sbc_hadgam' |
---|
| 659 | IF( sbc_cpl_alloc() /= 0 ) CALL ctl_stop( 'STOP', 'sbc_cpl_alloc : unable to allocate arrays' ) |
---|
| 660 | ENDIF |
---|
| 661 | |
---|
| 662 | ! ! =========================== ! |
---|
| 663 | ! ! Prepare Coupling fields ! |
---|
| 664 | ! ! =========================== ! |
---|
| 665 | ! |
---|
| 666 | ! x and y comp of ice velocity |
---|
| 667 | ! |
---|
| 668 | CALL cice2nemo(uvel,u_ice,'F', -1. ) |
---|
| 669 | CALL cice2nemo(vvel,v_ice,'F', -1. ) |
---|
| 670 | ! |
---|
| 671 | ! Ice concentration (CO_1) = a_i calculated at end of cice_sbc_out |
---|
| 672 | ! |
---|
| 673 | ! Snow and ice thicknesses (CO_2 and CO_3) |
---|
| 674 | ! |
---|
| 675 | DO jl = 1, ncat |
---|
| 676 | CALL cice2nemo( vsnon(:,:,jl,:), h_s(:,:,jl),'T', 1. ) |
---|
| 677 | CALL cice2nemo( vicen(:,:,jl,:), h_i(:,:,jl),'T', 1. ) |
---|
| 678 | END DO |
---|
| 679 | ! |
---|
| 680 | END SUBROUTINE cice_sbc_hadgam |
---|
| 681 | |
---|
| 682 | |
---|
| 683 | SUBROUTINE cice_sbc_final |
---|
| 684 | !!--------------------------------------------------------------------- |
---|
| 685 | !! *** ROUTINE cice_sbc_final *** |
---|
| 686 | !! ** Purpose: Finalize CICE |
---|
| 687 | !!--------------------------------------------------------------------- |
---|
| 688 | ! |
---|
| 689 | IF(lwp) WRITE(numout,*)'cice_sbc_final' |
---|
| 690 | ! |
---|
| 691 | CALL CICE_Finalize |
---|
| 692 | ! |
---|
| 693 | END SUBROUTINE cice_sbc_final |
---|
| 694 | |
---|
| 695 | |
---|
| 696 | SUBROUTINE cice_sbc_force (kt) |
---|
| 697 | !!--------------------------------------------------------------------- |
---|
| 698 | !! *** ROUTINE cice_sbc_force *** |
---|
| 699 | !! ** Purpose : Provide CICE forcing from files |
---|
| 700 | !! |
---|
| 701 | !!--------------------------------------------------------------------- |
---|
| 702 | !! ** Method : READ monthly flux file in NetCDF files |
---|
| 703 | !! |
---|
| 704 | !! snowfall |
---|
| 705 | !! rainfall |
---|
| 706 | !! sublimation rate |
---|
| 707 | !! topmelt (category) |
---|
| 708 | !! botmelt (category) |
---|
| 709 | !! |
---|
| 710 | !! History : |
---|
| 711 | !!---------------------------------------------------------------------- |
---|
| 712 | USE iom |
---|
| 713 | !! |
---|
| 714 | INTEGER, INTENT( in ) :: kt ! ocean time step |
---|
| 715 | !! |
---|
| 716 | INTEGER :: ierror ! return error code |
---|
| 717 | INTEGER :: ifpr ! dummy loop index |
---|
| 718 | !! |
---|
| 719 | CHARACTER(len=100) :: cn_dir ! Root directory for location of CICE forcing files |
---|
| 720 | TYPE(FLD_N), DIMENSION(jpfld) :: slf_i ! array of namelist informations on the fields to read |
---|
| 721 | TYPE(FLD_N) :: sn_snow, sn_rain, sn_sblm ! informations about the fields to be read |
---|
| 722 | TYPE(FLD_N) :: sn_top1, sn_top2, sn_top3, sn_top4, sn_top5 |
---|
| 723 | TYPE(FLD_N) :: sn_bot1, sn_bot2, sn_bot3, sn_bot4, sn_bot5 |
---|
| 724 | !! |
---|
| 725 | NAMELIST/namsbc_cice/ cn_dir, sn_snow, sn_rain, sn_sblm, & |
---|
| 726 | & sn_top1, sn_top2, sn_top3, sn_top4, sn_top5, & |
---|
| 727 | & sn_bot1, sn_bot2, sn_bot3, sn_bot4, sn_bot5 |
---|
| 728 | INTEGER :: ios |
---|
| 729 | !!--------------------------------------------------------------------- |
---|
| 730 | |
---|
| 731 | ! ! ====================== ! |
---|
| 732 | IF( kt == nit000 ) THEN ! First call kt=nit000 ! |
---|
| 733 | ! ! ====================== ! |
---|
| 734 | ! namsbc_cice is not yet in the reference namelist |
---|
| 735 | ! set file information (default values) |
---|
| 736 | cn_dir = './' ! directory in which the model is executed |
---|
| 737 | |
---|
| 738 | ! (NB: frequency positive => hours, negative => months) |
---|
| 739 | ! ! file ! frequency ! variable ! time intep ! clim ! 'yearly' or ! weights ! rotation ! landmask |
---|
| 740 | ! ! name ! (hours) ! name ! (T/F) ! (T/F) ! 'monthly' ! filename ! pairs ! file |
---|
| 741 | sn_snow = FLD_N( 'snowfall_1m' , -1. , 'snowfall' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 742 | sn_rain = FLD_N( 'rainfall_1m' , -1. , 'rainfall' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 743 | sn_sblm = FLD_N( 'sublim_1m' , -1. , 'sublim' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 744 | sn_top1 = FLD_N( 'topmeltn1_1m' , -1. , 'topmeltn1' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 745 | sn_top2 = FLD_N( 'topmeltn2_1m' , -1. , 'topmeltn2' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 746 | sn_top3 = FLD_N( 'topmeltn3_1m' , -1. , 'topmeltn3' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 747 | sn_top4 = FLD_N( 'topmeltn4_1m' , -1. , 'topmeltn4' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 748 | sn_top5 = FLD_N( 'topmeltn5_1m' , -1. , 'topmeltn5' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 749 | sn_bot1 = FLD_N( 'botmeltn1_1m' , -1. , 'botmeltn1' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 750 | sn_bot2 = FLD_N( 'botmeltn2_1m' , -1. , 'botmeltn2' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 751 | sn_bot3 = FLD_N( 'botmeltn3_1m' , -1. , 'botmeltn3' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 752 | sn_bot4 = FLD_N( 'botmeltn4_1m' , -1. , 'botmeltn4' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 753 | sn_bot5 = FLD_N( 'botmeltn5_1m' , -1. , 'botmeltn5' , .true. , .true. , ' yearly' , '' , '' , '' ) |
---|
| 754 | |
---|
| 755 | READ ( numnam_ref, namsbc_cice, IOSTAT = ios, ERR = 901) |
---|
| 756 | 901 IF( ios /= 0 ) CALL ctl_nam ( ios , 'namsbc_cice in reference namelist' ) |
---|
| 757 | |
---|
| 758 | READ ( numnam_cfg, namsbc_cice, IOSTAT = ios, ERR = 902 ) |
---|
| 759 | 902 IF( ios > 0 ) CALL ctl_nam ( ios , 'namsbc_cice in configuration namelist' ) |
---|
| 760 | IF(lwm) WRITE ( numond, namsbc_cice ) |
---|
| 761 | |
---|
| 762 | ! store namelist information in an array |
---|
| 763 | slf_i(jp_snow) = sn_snow ; slf_i(jp_rain) = sn_rain ; slf_i(jp_sblm) = sn_sblm |
---|
| 764 | slf_i(jp_top1) = sn_top1 ; slf_i(jp_top2) = sn_top2 ; slf_i(jp_top3) = sn_top3 |
---|
| 765 | slf_i(jp_top4) = sn_top4 ; slf_i(jp_top5) = sn_top5 ; slf_i(jp_bot1) = sn_bot1 |
---|
| 766 | slf_i(jp_bot2) = sn_bot2 ; slf_i(jp_bot3) = sn_bot3 ; slf_i(jp_bot4) = sn_bot4 |
---|
| 767 | slf_i(jp_bot5) = sn_bot5 |
---|
| 768 | |
---|
| 769 | ! set sf structure |
---|
| 770 | ALLOCATE( sf(jpfld), STAT=ierror ) |
---|
| 771 | IF( ierror > 0 ) THEN |
---|
| 772 | CALL ctl_stop( 'cice_sbc_force: unable to allocate sf structure' ) ; RETURN |
---|
| 773 | ENDIF |
---|
| 774 | |
---|
| 775 | DO ifpr= 1, jpfld |
---|
| 776 | ALLOCATE( sf(ifpr)%fnow(jpi,jpj,1) ) |
---|
| 777 | ALLOCATE( sf(ifpr)%fdta(jpi,jpj,1,2) ) |
---|
| 778 | END DO |
---|
| 779 | |
---|
| 780 | ! fill sf with slf_i and control print |
---|
| 781 | CALL fld_fill( sf, slf_i, cn_dir, 'cice_sbc_force', 'flux formulation for CICE', 'namsbc_cice' ) |
---|
| 782 | ! |
---|
| 783 | ENDIF |
---|
| 784 | |
---|
| 785 | CALL fld_read( kt, nn_fsbc, sf ) ! Read input fields and provides the |
---|
| 786 | ! ! input fields at the current time-step |
---|
| 787 | |
---|
| 788 | ! set the fluxes from read fields |
---|
| 789 | sprecip(:,:) = sf(jp_snow)%fnow(:,:,1) |
---|
| 790 | tprecip(:,:) = sf(jp_snow)%fnow(:,:,1)+sf(jp_rain)%fnow(:,:,1) |
---|
| 791 | ! May be better to do this conversion somewhere else |
---|
| 792 | qla_ice(:,:,1) = -rLsub*sf(jp_sblm)%fnow(:,:,1) |
---|
| 793 | topmelt(:,:,1) = sf(jp_top1)%fnow(:,:,1) |
---|
| 794 | topmelt(:,:,2) = sf(jp_top2)%fnow(:,:,1) |
---|
| 795 | topmelt(:,:,3) = sf(jp_top3)%fnow(:,:,1) |
---|
| 796 | topmelt(:,:,4) = sf(jp_top4)%fnow(:,:,1) |
---|
| 797 | topmelt(:,:,5) = sf(jp_top5)%fnow(:,:,1) |
---|
| 798 | botmelt(:,:,1) = sf(jp_bot1)%fnow(:,:,1) |
---|
| 799 | botmelt(:,:,2) = sf(jp_bot2)%fnow(:,:,1) |
---|
| 800 | botmelt(:,:,3) = sf(jp_bot3)%fnow(:,:,1) |
---|
| 801 | botmelt(:,:,4) = sf(jp_bot4)%fnow(:,:,1) |
---|
| 802 | botmelt(:,:,5) = sf(jp_bot5)%fnow(:,:,1) |
---|
| 803 | |
---|
| 804 | ! control print (if less than 100 time-step asked) |
---|
| 805 | IF( nitend-nit000 <= 100 .AND. lwp ) THEN |
---|
| 806 | WRITE(numout,*) |
---|
| 807 | WRITE(numout,*) ' read forcing fluxes for CICE OK' |
---|
| 808 | CALL FLUSH(numout) |
---|
| 809 | ENDIF |
---|
| 810 | |
---|
| 811 | END SUBROUTINE cice_sbc_force |
---|
| 812 | |
---|
| 813 | SUBROUTINE nemo2cice( pn, pc, cd_type, psgn) |
---|
| 814 | !!--------------------------------------------------------------------- |
---|
| 815 | !! *** ROUTINE nemo2cice *** |
---|
| 816 | !! ** Purpose : Transfer field in NEMO array to field in CICE array. |
---|
| 817 | #if defined key_nemocice_decomp |
---|
| 818 | !! |
---|
| 819 | !! NEMO and CICE PE sub domains are identical, hence |
---|
| 820 | !! there is no need to gather or scatter data from |
---|
| 821 | !! one PE configuration to another. |
---|
| 822 | #else |
---|
| 823 | !! Automatically gather/scatter between |
---|
| 824 | !! different processors and blocks |
---|
| 825 | !! ** Method : A. Ensure all haloes are filled in NEMO field (pn) |
---|
| 826 | !! B. Gather pn into global array (png) |
---|
| 827 | !! C. Map png into CICE global array (pcg) |
---|
| 828 | !! D. Scatter pcg to CICE blocks (pc) + update haloes |
---|
| 829 | #endif |
---|
| 830 | !!--------------------------------------------------------------------- |
---|
| 831 | CHARACTER(len=1), INTENT( in ) :: & |
---|
| 832 | cd_type ! nature of pn grid-point |
---|
| 833 | ! ! = T or F gridpoints |
---|
| 834 | REAL(wp), INTENT( in ) :: & |
---|
| 835 | psgn ! control of the sign change |
---|
| 836 | ! ! =-1 , the sign is modified following the type of b.c. used |
---|
| 837 | ! ! = 1 , no sign change |
---|
| 838 | REAL(wp), DIMENSION(jpi,jpj) :: pn |
---|
| 839 | #if !defined key_nemocice_decomp |
---|
| 840 | REAL(wp), DIMENSION(jpiglo,jpjglo) :: png2 |
---|
| 841 | REAL (kind=dbl_kind), dimension(nx_global,ny_global) :: pcg |
---|
| 842 | #endif |
---|
| 843 | REAL (kind=dbl_kind), dimension(nx_block,ny_block,max_blocks) :: pc |
---|
| 844 | INTEGER (int_kind) :: & |
---|
| 845 | field_type, &! id for type of field (scalar, vector, angle) |
---|
| 846 | grid_loc ! id for location on horizontal grid |
---|
| 847 | ! (center, NEcorner, Nface, Eface) |
---|
| 848 | |
---|
| 849 | INTEGER :: ji, jj, jn ! dummy loop indices |
---|
| 850 | !!--------------------------------------------------------------------- |
---|
| 851 | |
---|
| 852 | ! A. Ensure all haloes are filled in NEMO field (pn) |
---|
| 853 | |
---|
| 854 | CALL lbc_lnk( 'sbcice_cice', pn , cd_type, psgn ) |
---|
| 855 | |
---|
| 856 | #if defined key_nemocice_decomp |
---|
| 857 | |
---|
| 858 | ! Copy local domain data from NEMO to CICE field |
---|
| 859 | pc(:,:,1)=0.0 |
---|
| 860 | DO jj=2,ny_block-1 |
---|
| 861 | DO ji=2,nx_block-1 |
---|
| 862 | pc(ji,jj,1)=pn(ji-1+ji_off,jj-1+jj_off) |
---|
| 863 | ENDDO |
---|
| 864 | ENDDO |
---|
| 865 | |
---|
| 866 | #else |
---|
| 867 | |
---|
| 868 | ! B. Gather pn into global array (png) |
---|
| 869 | |
---|
| 870 | IF( jpnij > 1) THEN |
---|
| 871 | CALL mppsync |
---|
| 872 | CALL mppgather (pn,0,png) |
---|
| 873 | CALL mppsync |
---|
| 874 | ELSE |
---|
| 875 | png(:,:,1)=pn(:,:) |
---|
| 876 | ENDIF |
---|
| 877 | |
---|
| 878 | ! C. Map png into CICE global array (pcg) |
---|
| 879 | |
---|
| 880 | ! Need to make sure this is robust to changes in NEMO halo rows.... |
---|
| 881 | ! (may be OK but not 100% sure) |
---|
| 882 | |
---|
| 883 | IF(nproc==0) THEN |
---|
| 884 | ! pcg(:,:)=0.0 |
---|
| 885 | DO jn=1,jpnij |
---|
| 886 | DO jj=nldjt(jn),nlejt(jn) |
---|
| 887 | DO ji=nldit(jn),nleit(jn) |
---|
| 888 | png2(ji+nimppt(jn)-1,jj+njmppt(jn)-1)=png(ji,jj,jn) |
---|
| 889 | ENDDO |
---|
| 890 | ENDDO |
---|
| 891 | ENDDO |
---|
| 892 | DO jj=1,ny_global |
---|
| 893 | DO ji=1,nx_global |
---|
| 894 | pcg(ji,jj)=png2(ji+ji_off,jj+jj_off) |
---|
| 895 | ENDDO |
---|
| 896 | ENDDO |
---|
| 897 | ENDIF |
---|
| 898 | |
---|
| 899 | #endif |
---|
| 900 | |
---|
| 901 | SELECT CASE ( cd_type ) |
---|
| 902 | CASE ( 'T' ) |
---|
| 903 | grid_loc=field_loc_center |
---|
| 904 | CASE ( 'F' ) |
---|
| 905 | grid_loc=field_loc_NEcorner |
---|
| 906 | END SELECT |
---|
| 907 | |
---|
| 908 | SELECT CASE ( NINT(psgn) ) |
---|
| 909 | CASE ( -1 ) |
---|
| 910 | field_type=field_type_vector |
---|
| 911 | CASE ( 1 ) |
---|
| 912 | field_type=field_type_scalar |
---|
| 913 | END SELECT |
---|
| 914 | |
---|
| 915 | #if defined key_nemocice_decomp |
---|
| 916 | ! Ensure CICE halos are up to date |
---|
| 917 | CALL ice_HaloUpdate (pc, halo_info, grid_loc, field_type) |
---|
| 918 | #else |
---|
| 919 | ! D. Scatter pcg to CICE blocks (pc) + update halos |
---|
| 920 | CALL scatter_global(pc, pcg, 0, distrb_info, grid_loc, field_type) |
---|
| 921 | #endif |
---|
| 922 | |
---|
| 923 | END SUBROUTINE nemo2cice |
---|
| 924 | |
---|
| 925 | SUBROUTINE cice2nemo ( pc, pn, cd_type, psgn ) |
---|
| 926 | !!--------------------------------------------------------------------- |
---|
| 927 | !! *** ROUTINE cice2nemo *** |
---|
| 928 | !! ** Purpose : Transfer field in CICE array to field in NEMO array. |
---|
| 929 | #if defined key_nemocice_decomp |
---|
| 930 | !! |
---|
| 931 | !! NEMO and CICE PE sub domains are identical, hence |
---|
| 932 | !! there is no need to gather or scatter data from |
---|
| 933 | !! one PE configuration to another. |
---|
| 934 | #else |
---|
| 935 | !! Automatically deal with scatter/gather between |
---|
| 936 | !! different processors and blocks |
---|
| 937 | !! ** Method : A. Gather CICE blocks (pc) into global array (pcg) |
---|
| 938 | !! B. Map pcg into NEMO global array (png) |
---|
| 939 | !! C. Scatter png into NEMO field (pn) for each processor |
---|
| 940 | !! D. Ensure all haloes are filled in pn |
---|
| 941 | #endif |
---|
| 942 | !!--------------------------------------------------------------------- |
---|
| 943 | |
---|
| 944 | CHARACTER(len=1), INTENT( in ) :: & |
---|
| 945 | cd_type ! nature of pn grid-point |
---|
| 946 | ! ! = T or F gridpoints |
---|
| 947 | REAL(wp), INTENT( in ) :: & |
---|
| 948 | psgn ! control of the sign change |
---|
| 949 | ! ! =-1 , the sign is modified following the type of b.c. used |
---|
| 950 | ! ! = 1 , no sign change |
---|
| 951 | REAL(wp), DIMENSION(jpi,jpj) :: pn |
---|
| 952 | |
---|
| 953 | #if defined key_nemocice_decomp |
---|
| 954 | INTEGER (int_kind) :: & |
---|
| 955 | field_type, & ! id for type of field (scalar, vector, angle) |
---|
| 956 | grid_loc ! id for location on horizontal grid |
---|
| 957 | ! (center, NEcorner, Nface, Eface) |
---|
| 958 | #else |
---|
| 959 | REAL (kind=dbl_kind), dimension(nx_global,ny_global) :: pcg |
---|
| 960 | #endif |
---|
| 961 | |
---|
| 962 | REAL (kind=dbl_kind), dimension(nx_block,ny_block,max_blocks) :: pc |
---|
| 963 | |
---|
| 964 | INTEGER :: ji, jj, jn ! dummy loop indices |
---|
| 965 | |
---|
| 966 | |
---|
| 967 | #if defined key_nemocice_decomp |
---|
| 968 | |
---|
| 969 | SELECT CASE ( cd_type ) |
---|
| 970 | CASE ( 'T' ) |
---|
| 971 | grid_loc=field_loc_center |
---|
| 972 | CASE ( 'F' ) |
---|
| 973 | grid_loc=field_loc_NEcorner |
---|
| 974 | END SELECT |
---|
| 975 | |
---|
| 976 | SELECT CASE ( NINT(psgn) ) |
---|
| 977 | CASE ( -1 ) |
---|
| 978 | field_type=field_type_vector |
---|
| 979 | CASE ( 1 ) |
---|
| 980 | field_type=field_type_scalar |
---|
| 981 | END SELECT |
---|
| 982 | |
---|
| 983 | CALL ice_HaloUpdate (pc, halo_info, grid_loc, field_type) |
---|
| 984 | |
---|
| 985 | |
---|
| 986 | pn(:,:)=0.0 |
---|
[13295] | 987 | DO_2D( 1, 0, 1, 0 ) |
---|
[12983] | 988 | pn(ji,jj)=pc(ji+1-ji_off,jj+1-jj_off,1) |
---|
| 989 | END_2D |
---|
| 990 | |
---|
| 991 | #else |
---|
| 992 | |
---|
| 993 | ! A. Gather CICE blocks (pc) into global array (pcg) |
---|
| 994 | |
---|
| 995 | CALL gather_global(pcg, pc, 0, distrb_info) |
---|
| 996 | |
---|
| 997 | ! B. Map pcg into NEMO global array (png) |
---|
| 998 | |
---|
| 999 | ! Need to make sure this is robust to changes in NEMO halo rows.... |
---|
| 1000 | ! (may be OK but not spent much time thinking about it) |
---|
| 1001 | ! Note that non-existent pcg elements may be used below, but |
---|
| 1002 | ! the lbclnk call on pn will replace these with sensible values |
---|
| 1003 | |
---|
| 1004 | IF(nproc==0) THEN |
---|
| 1005 | png(:,:,:)=0.0 |
---|
| 1006 | DO jn=1,jpnij |
---|
| 1007 | DO jj=nldjt(jn),nlejt(jn) |
---|
| 1008 | DO ji=nldit(jn),nleit(jn) |
---|
| 1009 | png(ji,jj,jn)=pcg(ji+nimppt(jn)-1-ji_off,jj+njmppt(jn)-1-jj_off) |
---|
| 1010 | ENDDO |
---|
| 1011 | ENDDO |
---|
| 1012 | ENDDO |
---|
| 1013 | ENDIF |
---|
| 1014 | |
---|
| 1015 | ! C. Scatter png into NEMO field (pn) for each processor |
---|
| 1016 | |
---|
| 1017 | IF( jpnij > 1) THEN |
---|
| 1018 | CALL mppsync |
---|
| 1019 | CALL mppscatter (png,0,pn) |
---|
| 1020 | CALL mppsync |
---|
| 1021 | ELSE |
---|
| 1022 | pn(:,:)=png(:,:,1) |
---|
| 1023 | ENDIF |
---|
| 1024 | |
---|
| 1025 | #endif |
---|
| 1026 | |
---|
| 1027 | ! D. Ensure all haloes are filled in pn |
---|
| 1028 | |
---|
| 1029 | CALL lbc_lnk( 'sbcice_cice', pn , cd_type, psgn ) |
---|
| 1030 | |
---|
| 1031 | END SUBROUTINE cice2nemo |
---|
| 1032 | |
---|
| 1033 | #else |
---|
| 1034 | !!---------------------------------------------------------------------- |
---|
| 1035 | !! Default option Dummy module NO CICE sea-ice model |
---|
| 1036 | !!---------------------------------------------------------------------- |
---|
| 1037 | CONTAINS |
---|
| 1038 | |
---|
| 1039 | SUBROUTINE sbc_ice_cice ( kt, ksbc ) ! Dummy routine |
---|
| 1040 | IMPLICIT NONE |
---|
| 1041 | INTEGER, INTENT( in ) :: kt, ksbc |
---|
| 1042 | WRITE(*,*) 'sbc_ice_cice: You should not have seen this print! error?', kt |
---|
| 1043 | END SUBROUTINE sbc_ice_cice |
---|
| 1044 | |
---|
| 1045 | SUBROUTINE cice_sbc_init (ksbc, Kbb, Kmm) ! Dummy routine |
---|
| 1046 | IMPLICIT NONE |
---|
| 1047 | INTEGER, INTENT( in ) :: ksbc |
---|
| 1048 | INTEGER, INTENT( in ) :: Kbb, Kmm |
---|
| 1049 | WRITE(*,*) 'cice_sbc_init: You should not have seen this print! error?', ksbc |
---|
| 1050 | END SUBROUTINE cice_sbc_init |
---|
| 1051 | |
---|
| 1052 | SUBROUTINE cice_sbc_final ! Dummy routine |
---|
| 1053 | IMPLICIT NONE |
---|
| 1054 | WRITE(*,*) 'cice_sbc_final: You should not have seen this print! error?' |
---|
| 1055 | END SUBROUTINE cice_sbc_final |
---|
| 1056 | |
---|
| 1057 | #endif |
---|
| 1058 | |
---|
| 1059 | !!====================================================================== |
---|
| 1060 | END MODULE sbcice_cice |
---|